Honeywell RTH230B priročnik

Honeywell RTH230B
9.2 · 2
PDF priročnik
 · 4 strani
Angleščina
priročnikHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Tukaj si oglejte priročnik za Honeywell RTH230B, brezplačno. Ta priročnik spada v kategorijo termostat in ga je ocenilo 2 ljudi s povprečjem 9.2. Ta priročnik je na voljo v naslednjih jezikih: Angleščina . Imate vprašanje o Honeywell RTH230B ali potrebujete pomoč? Tukaj postavite svoje vprašanje

Potrebujete pomoč?

Imate vprašanje o Honeywell , odgovora pa ni v priročniku?

  • Prejmite posodobitve o rešitvah
  • Dobite odgovore na vaša vprašanja

Vprašanje in odgovor

Število vprašanj: 0

Honeywell RTH230B je digitalni termostat za ogrevanje in hlajenje domov. Omogoča uporabniku preprosto in učinkovito nadziranje temperature v prostorih s svojim intuitivnim zaslonom. Lahko ga uporabljate za programiranje tedenskega urnika in nadzorovati do dva različna območja temperature. Termostat je opremljen z gumbe in funkcijami, ki so enostavne za uporabo in vključuje talno ogrevanje ter programsko zaporo. Honeywell RTH230B je zasnovan za preprosto vgradnjo in delovanje s številnimi ogrevalnimi in hladilnimi sistemi. Zagotavlja natančen nadzor nad temperaturo, kar vam omogoča udobno bivanje v vašem domu. Zahvaljujoč svojim oblikovnim lastnostim, je Honeywell RTH230B primeren za vsak dom in ga bo učinkovito ogrel ali ohladil v prostorih, kjer ga boste uporabljali. Celotna zasnova Honeywell RTH230B je ustvarjena tako, da je izdelan iz kakovostnih materialov za zagotavljanje zanesljivosti in vzdržljivosti. Termostat vsebuje tudi varnostne funkcije, ki zagotavljajo varnost in preprečujejo poškodbe in nevarnosti ogrevanja. Overall, Honeywell RTH230B je učinkovit termostat, ki vam omogoča enostavno nadziranje vašega gospodinjstva, tako da ste vselej udobni in prijetno bivajte v vašem domu.

Splošno
Blagovna znamkaHoneywell
ModelRTH230B
Izdelektermostati
JezikAngleščina
Vrsta datotekeUporabniški priročnik (PDF)

Ne najdete odgovora na svoje vprašanje v priročniku? Odgovor na svoje vprašanje lahko najdete spodaj v pogostih vprašanjih o: Honeywell RTH230B.

Kje je najbolje namestiti termostat?

Najboljše mesto za termostat je soba, kjer preživite največ časa, običajno je to dnevna soba ali kuhinja. Termostat postavite približno meter in pol nad tla, ne na soncu in ne na zunanji steni.

Kaj je mrtvi pas termostata?

Če ima vaš termostat mrtvi pas, je vaša namestitev tako rekoč »v mirovanju«. Termostat se vklopi le, če na primer razlika odstopa za več kot 2 ˚C od nastavljene sobne temperature.

Kakšna je idealna sobna temperatura?

Za večino ljudi je idealna sobna temperatura med 19 in 22 stopinjami Celzija.

Je priročnik za Honeywell RTH230B na voljo v Slovenščina?

Žal priročnik za Honeywell RTH230B ni na voljo v Slovenščina . Ta priročnik je na voljo v Angleščina .

Ali vašega vprašanja ni na seznamu? Tukaj postavite svoje vprašanje

Ni rezultatov